Click below or on the picture below to see step by step makeover
Below we have a bronze base with bronze reflective and gold on top
Bronze base with bronze reflective topped with Starfire
above and below
Bronze reflective above
This is a typical fireplace before and below is our after
The 6 pictures below are of an antique coal basket using bronze, bronze reflective and starfire
The 6 pictures above are of an antique coal basket using bronze, bronze reflective and starfire
Fire pit below has:
Bronze base, 3/16 amber, Bronze reflective and yellow topper.
The 2 pictures below have bronze, bronze reflective, black, black reflective and pale cobalt blue topper.
The 3 pictures below have bronze, bronze reflective, gray and gray reflective with the outside of the fireplace painted medium brown with fireplace paint.
The indoor fire table below has:
Bronze, black, emerald green, reflective green, black reflective and gold
The fireplace below has: Bronze and reflective, black and reflective and amber
The fireplace below has bronze and bronze reflective installed.
On this page we will be posting some real cool fire flame pictures. Your more than welcome to send yours.
This fireplace has:
A black silicone base
But you can't see that now. We will be posting daytime pictures so you can see the actual glass. We will be posting the yellow flames as well. We will tell you how to do this in the near future, really!
I am very happy with my “new” gas fireplace. I thought I would share with you the enclosed photos taken with an ordinary digital camera with no ambient light except the fire itself.
The camera was placed in various locations around the fire on the hearth proper.
Unfortunately the stills cannot depict the fire action.
What is amazing about the fire is the low spread out blue flame pattern instead of the conventional tall yellow flames in the middle.
The fireplace is open on three sides 30”x40”,
The pit was filled with coarse bagged lava rock form Home Depot approximately 1” deep to the bottom of the U shaped burner gas pipe with the holes pointing down.
It was then topped with Moderustic fine lava rock to fill in the voids on the top leaving the bottom of the burner only slightly submerged below the layer of the finer lava rock.
The next layer was black sand followed by S----- C-----.
The sand was mounded in the center over the burners. A sprinkling of grey glass over the SC and a topper of Bronze ½” glass was sprinkled over the smaller sized matrix to finish.
The final product is very dark and reflective with tiny reflections off of the s----- c------ and larger reflections off of the gradated glass during the day and in ambient light.
It looks a little like a lava field that you might run across in the Mojave Desert near Barstow.
Not at all showy, yet very subtle to the view in daylight.
The coarse lava rock on the bottom layer, with the finer layer on top to keep the gas in longer, acts as manifold carrying gas to all portion of the firebox floor covered with that material.
I stopped the coarse rock short of the metal posts in a semi circular shape in plan and backfilled with sand so that the flame would not reach the posts.
The visual result around the posts is that the gas reaching the end of the coarse material immediately goes upward creating a flowing arc of fire around the posts.
This is seen as a blur in the photos.
The underlying coarse rock distributes the gas pretty evenly across the firebox floor creating a even matrix of small flames on the surface as it works its way up through the media.
The extreme perimeter appears more active.
There are more constant more steady flames from the mound. Because there is less gas at the perimeter, the gas there burns in horizontal spurts and appears like lightning bolts licking the edges of the firebox.
There are small vortexes of fire that form and sometimes work there way around the base of the mound on the center but usually preferring a particular area to hang out.
The overall effect is one of a dispersed flame.
As if the entire bed of the fireplace is afire with a low blue flame. With all the lights out in the room it is quite magical.
Not at all anything like a conventional yellow flame in the center. Due to the dispersion of the flame across the large firebox area, there is a lot of heat generated and dispersed into the room instead of up the flue.
This is not a design for summer time nights.
Everyone who witnesses this flame is impressed with the “light show” quality of the burn.
In the future I plan to change out the media and experiment with different ways to direct the gas and resultant flame to achieve different effects.
Next time I am thinking of laying a pattern of coarse rock and infilling between the “arms” of coarse rock with sand so that the gas will follow the “arms” and come up in more predictable places, perhaps creating little vortexes or pyres at the ends of the “arms”.
The fireplace below has bronze, bronze reflective, Ice, gold and yellow amber topper.
This fireplace is in Shawano, Wisconsin at the Cotton Patch Restaurant.
Now for the after pictures! This was a custom propane burner which was under all of the glass!
The fire pit below is in Malibu California which no one could figure out how to do what we did. The customer didn't want to see the fire pit hood anymore. So we just raised it. And everyone said it couldn't be done! This is what we like to do, take imagination and make it a reality. The base was provided by the customer we just supplied the "raise the hood" and the ring and bronze and bronze reflective glass.
The vent went up 20 feet. E mail us and we will tell you how this was done.
The fireplace below is in Rancho Mirage just east of Palm Springs California. This is a direct vent fireplace and we used a bronze base glass with bronze reflective on top. We use the original burner as it would do just fine. We are also cladding the bras with brushed stainless steel and we will post the pictures as soon as we get them. We did two identical fireplaces in this home. One in the master and the other in the family room. You can tell by the back ground.
The pictures below will show you how to install a propane burner and valve in your fire pit without drilling a hole in the side of your fire pit with our FPPK (fire pit propane kit). This was install in Calabasas California with bronze and bronze reflective on top. The fire pit has 10" solid sides which made this a good candidate for the FPPK to be installed on the inside wall. This is a propane fire pit and we do calibrate every valve to every ring we install to eliminate back flow and any problems or issues that may happen. We also install the proper air mixer to insure a clean burn as we eliminate the soot know to be produced by propane. If you have a propane fire pit you know what I am talking about.
The fireplace below is a before and after and a "how to" make it low and lean. A more contemporary look. This is a self install by Rich Kamins and one very nice job!. He used a bronze and bronze reflective base glass. Topper with a bit of starfire. Ice Ice Ice and about 2 pounds of copper ruby red topper for a splash of color.
A few bricks and some drywall
Some sand under the burner for filler to raise the base glass.
And here you have one nice finished fireplace.
The fireplace below is a self install with a 2" base of crushed lava
painted with metallic warm brown paint
18 18 double burner
bronze base glass
ice ice ice
dark red orange topper
The fire pit below was designed and built by Jeffrey Stoutenborough in Santa Barbara, California.
He started with a bronze base,
bronze reflective on top,
Ice Ice Ice.
dark red orange and
blue green and a few large rocks left in place.
The fireplace below has a base of gray and bronze topped with bronze and gray reflective.
The fireplace below has a base of bronze with bronze reflective and starfire on top.
This is the back side of the peninsula fireplace.
Click HERE or on the picture below to see all of the pictures of the Corten Steel Fire Pit!